|
|
|
|
Top
Trigger Models
|
|
|
A
special top trigger (in place of
the trigger below the horizontal
deadbolt) is available for use on
doors with multi-point locking and
the surface-bolt option which are
openly exposed to the general public
and where there is a high likelihood
of
mis-use
(such as rear exit doors in public
housing).
8200V Series (used on pairs of doors)
do not require a center mullion.
|
|
|
|
|
Cylinder
Dogging |
 |
The
interior lever is locked in the downward
position which keeps the latch retracted.
The door can then be pushed or pulled
open. The lever is released and the
door re-locked by use of key. Exiting
is possible at all times, regardless
of mode. |
|
|
|
| |
|
Electric
Release Options
|
|
|
24vAC,
30va transformer required |
|
|
24vDC
transformer required |
|
|
24vDC,
Fail-Safe Re-Entry Function |
|
|
|
Latch
Position Switch
Latch
position switch for use with alarms |
|
|
|
Key
Usage Signal Switch
For
use with access control systems. Sends
a signal to the access control system
that a key (not card) was used for
entry. |
|
|
|
Access
Control Cut-Off Switch
Access control
systems can be complicated to program and
turn on and off. Frequently a computer is
needed to change status, time zones, etc.
The cut-off switch feature allows a clockwise
rotation of the key to toggle the access
control system on or off. The supervisor
does not need to have any programming skills
to turn the system off for a defined period
(after hours, weekend, etc.) or turn it
back on. |
|
|
|
Classroom
Function
Key unlocks
lever for extended period, until key is
used to re-lock lever. Lock functions in
passage mode while exterior lever is in
unlocked mode. |
|
|
|
R-T-E
Switch
Optional
signal switch for interior trim for use
with alarmed or access control doors. Depressing
the interior lever actuates the switch. |
|
|
Cylinder
Protector
(UG Trim Only) |
|
|
Full
face steel cylinder protector is standard
for regular cylinders |
|
|
|
"BEST"-
type IC core cylinders require a 8"
plug opening |
|
|
|
Yale IC core cylinders require an
oval keyhole opening |
|
|
|
|
8
' Lead Length
Eliminates
wiring connections in the lock area of the
door |
|
Vertical
Deadbolt Control
See Separate
Catalog Cut |
|
|
EDGE
PLATES
| Doors
which have inverted U-channels do
not require special edge preparations,
|
| as
they will use the elevated |
|
|
edge plate which fits into the channel.
A flat edge plate is available for
wood doors or flush HM doors. |
|
|
|
VANDAL
RESISTANCE
|
|
|
Hardened
steel cylinder protectors
on both units.
|
|
|
"Slip-Clutch"
Lever Handle:
Standard with UG & GG
Lever will "breakaway" if
forced, but does not unlock door.
Lever can be simply reset by lifting
back to original (horizontal) position.
|
|
"Slip-Off"
Pull Handle:
Spoils attempts to rip the door from
the frame by tying a chain to the
lever and pulling with a car. Pull
handle will separate from guard plate
if forced. |
|
|
|
Requirements
|
•
|
Min.
1-3/4" door thickness |
|
•
|
4-7/8"
frame strike prep |
| • |
1-1/4"
x 8" door mortise prep |
| • |
Vertically-stiffened
hollow-metal door (For internally
mounted multi-point locks |
|
|
|
| |
| |
